3ware 9500-12 was built initialy at 3.6TiB since migrated to 5.9Tib however NL is still seeing it as 3.6 and consequently is alarming due to thinking it is nearly full.
[img] [ NASLite-M2 ] - Administration Utility - NASLite-M2 v1.63 08-2010
DISK-2 CONFIGURATION MENU
Disk Model: AMCC 9500S-12 DISK, v.2.08
Interface: DEVICE-SDA, HOST-0, BUS-0, TARGET-0, LUN-0
Status: DISK IS MOUNTED!
Usage: 3.6T / 3.5T / 54.5G / 99% - ( Size / Used / Free / Used% )
1 - Export Disk-2 [ RW ] (RW, RO, --)
2 - Set Disk-2 Capacity Alarm [ 99 ] (75, 80, 85, 90, 95, 99, --)
* - Set Disk-2 S.M.A.R.T. [ -- ] (ON, --)
* - Run Disk-2 Extended S.M.A.R.T. Self-Test
5 - Check Disk-2 Filesystem
* - Check and Repair Disk-2 Filesystem
7 - Apply Journal to Disk-2 Filesystem
8 - Format Disk-2
9 - Mirror to Disk-2 from [ NONE ]
R - Return To Storage Configuration Menu
Select: >[/img]
Log is saying that array is reported correctly.
Quote:
Nov 7 10:44:52 [2] eth1: dma_rwctrl[763f0000] dma_mask[64-bit]
Nov 7 10:44:52 [4] 3ware 9000 Storage Controller device driver for Linux v2.26.02.012.
Nov 7 10:45:14 [4] 3w-9xxx: scsi0: AEN: WARNING (0x04:0x0042): Primary DCB read error occurred:port=9, error=0x208.
Nov 7 10:45:14 [4] 3w-9xxx: scsi0: AEN: WARNING (0x04:0x0042): Primary DCB read error occurred:port=10, error=0x208.
Nov 7 10:45:14 [2] scsi0 : 3ware 9000 Storage Controller
Nov 7 10:45:14 [4] 3w-9xxx: scsi0: Found a 3ware 9000 Storage Controller at 0xfd100000, IRQ: 29.
Nov 7 10:45:14 [4] 3w-9xxx: scsi0: Firmware FE9X 2.08.00.009, BIOS BE9X 2.03.01.052, Ports: 12.
Nov 7 10:45:14 [3] scsi 0:0:0:0: Direct-Access AMCC 9500S-12 DISK 2.08 PQ: 0 ANSI: 3
Nov 7 10:45:15 [2] ide-gd driver 1.18
Nov 7 10:45:15 [2] hda: max request size: 512KiB
Nov 7 10:45:15 [2] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
Nov 7 10:45:15 [2] hda: cache flushes supported
Nov 7 10:45:15 [2] hda:
Nov 7 10:45:15 [2] hda1
Nov 7 10:45:15 [2] hdc: max request size: 128KiB
Nov 7 10:45:15 [2] hdc: 249984 sectors (127 MB) w/1KiB Cache, CHS=248/16/63
Nov 7 10:45:15 [2] hdc:
Nov 7 10:45:15 [2] hdc1
Nov 7 10:45:15 [2] ide-cd driver 5.00
Nov 7 10:45:15 [2] ide-cd: hdb: ATAPI 24X CD-ROM drive, 128kB Cache
Nov 7 10:45:15 [2] Uniform CD-ROM driver Revision: 3.20
Nov 7 10:45:15 [4] Driver 'sd' needs updating - please use bus_type methods
Nov 7 10:45:15 [3] sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Nov 7 10:45:15 [3] sd 0:0:0:0: [sda] 11718623232 512-byte hardware sectors: (5.99 TB/5.45 TiB)
Nov 7 10:45:15 [3] sd 0:0:0:0: [sda] Write Protect is off
Nov 7 10:45:15 [1] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
Nov 7 10:45:15 [3] sd 0:0:0:0: [sda] Write cache: enabled, read cache: disabled, doesn't support DPO or FUA
Nov 7 10:45:15 [3] sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Nov 7 10:45:15 [2] sda:
Suspect this is a Bug
Comments please.
p.s. this is with v1.63
Doug